Brass Fretwire

[Tom Wikoff]

I'm trying to locate some replacement brass fretwire for a vintage guitar (circa '30s or '40s). These measurements are not precise... the crown width is approx. 0.8mm... the crown height is approx. 1.0mm... the tang is approx. 1.2mm. A Stew Mac rep sent me to this forum as they did not carry such. Can you help me?

[Bob Gramann]

If all else fails, you might be able to use evo fretwire (lmi sells it) and ignore the slight difference in shading.

[Chuck Tweedy]

Tom, First off, brass frets are very soft, and are used today on toy instruments from China. There must be someone making it there. You can't really get it from a lutherie supply place. EDIT: I take that back - Guitar Parts sells brass fretwire.


However - your specs seem to indicate that this instrument has bar frets. The crown width of 0.8mm is a pretty clear sign of that.
Are these frets just rectangular wire pressed into slots in the board????

[Tom Wikoff]

Tom, First off, brass frets are very soft, and are used today on toy instruments from China. There must be someone making it there. You can't really get it from a lutherie supply place. EDIT: I take that back - Guitar Parts sells brass fretwire.


However - your specs seem to indicate that this instrument has bar frets. The crown width of 0.8mm is a pretty clear sign of that.
Are these frets just rectangular wire pressed into slots in the board????

No, this is definitely fretwire. It has barbs. The frets were installed on a very old parlor size guitar. Here is a link to the photo-sharing website where I've posted quite a few pictures of the instrument. https://grandpadownsguitar.shutterfly.com/pictures

[Chuck Tweedy]

The closest thing to that shape/size wire would be mandolin wire - Stew-Mac sells it. It is not brass.
You will likely not be able to find brass wire that shape.
The fingerboard on that instrument looks to be falling apart. You could replace the entire board and give it some good frets.
Are you looking to restore or to make the instrument serviceable again??

[Tom Wikoff]

The closest thing to that shape/size wire would be mandolin wire - Stew-Mac sells it. It is not brass.
You will likely not be able to find brass wire that shape.
The fingerboard on that instrument looks to be falling apart. You could replace the entire board and give it some good frets.
Are you looking to restore or to make the instrument serviceable again??

No, it will be a "wallhanger"... a conversation piece. It belonged to my maternal grandfather. The best guess is that it is a Kay Del Oro sold through the Spiegel catalog. I have not found a picture of one just like it anywhere.

[Chuck Tweedy]

Oh, well then you don't need any fretwire at all!!
You're all set then.

[David Collins]

Sorry I missed this post earlier - if you still need some, I have loads of old brass wire. Not sure about the dimensions, but I know I have a few pounds of it laying around the shop, and can check the size tomorrow.

It's so soft I would never use it on clients' guitars, but if it's just for a wall hanger, that's what I use it for myself. Used a whole lot of it on this one -

I'd be happy to send you some if you still need it.

[David King]

Nice CAD spline rendering David.

[David Collins]

Nice CAD spline rendering David.

Ha! I hadn't looked at it that way, but now that you mention it...

It's an L-00 model made entirely of old fret wire soldered together.

[Jason Rodgers]

Tom, First off, brass frets are very soft, and are used today on toy instruments from China. There must be someone making it there. You can't really get it from a lutherie supply place. EDIT: I take that back - Guitar Parts sells brass fretwire.


However - your specs seem to indicate that this instrument has bar frets. The crown width of 0.8mm is a pretty clear sign of that.
Are these frets just rectangular wire pressed into slots in the board????

I don't know if you're a GAL member and get the American Lutherie quarterly (you should!), but the new issue #125 has a "Meet the Maker" article on Oregon banjo maker Doc Huff. In the article he describes how he builds his fretboards: the frets are very thin brass stock, inlaid flush, then scalloped between to reveal a crown. Very interesting method, but it's part of the whole design and aesthetic of his instruments.

[Clay Schaeffer]

"I don't know if you're a GAL member and get the American Lutherie quarterly (you should!), but the new issue #125 has a "Meet the Maker" article on Oregon banjo maker Doc Huff. In the article he describes how he builds his fretboards: the frets are very thin brass stock, inlaid flush, then scalloped between to reveal a crown. Very interesting method, but it's part of the whole design and aesthetic of his instruments."

Some of the lute bodied guitars have a similarly scalloped fretboard." What's old is new"